This standard specifies the safety rules for the construction and installation of permanently installed new electric service lifts with traction or positive drive, or hydraulic service lifts defined as lifting equipment, serving defined landing levels, having a car, the interior of which is regarded as inaccessible to persons on account of its dimensions and means of construction, suspended by ropes or chains or supported by a ram and moving between rigid vertical guide rails or guide rails whose inclination to the vertical does not exceed 15° and driven electrically or hydraulically. This standard covers service lifts with rated load not exceeding 300 kilogrammes and not intended to move persons. In addition to the requirements of this standard supplementary requirements shall be considered in special cases (potentially explosive atmosphere, extreme climate conditions, seismic conditions, transporting dangerous goods, etc.). This standard does not cover: a) service lifts with drives other than stated in; b) important modifications (see annex E) to a service lift installed before this standard is brought into application; c) lifting appliances, such as paternosters, mines lifts, theatrical lifts, appliances with automatic caging, skips and hoists for building and public works sites, ships' hoists, platforms for exploration or drilling at sea, construction and maintenance appliances; d) installations where the inclination of the guide rails to the vertical exceeds 15°; e) safety during transport, installation, repairs and dismantling of service lifts; f) the use of glass for the walls of the well, for the car and for the landing doors including the vision panels. However, this standard may usefully be taken as a basis. Noise and vibrations are not dealt with in this standard because these are not relevant to the safe use of the service lift. Fire propagation is not dealt with in this standard. To satisfy the condition of inaccessibility to the car, the car dimensions shall not exceed: a) for floor area, 1,0 m2; b) for depth, 1,0 m; c) for height, 1,20 m. The height of 1,20 m shall not be limited if the car comprises several permanent compartments, each of which satisfies the above requirements. In particular, lifting equipment intended exclusively for the transportation of goods, but having a car with dimensions exceeding any one of the figures above shall not be entered in the category 'service lifts'. This standard covers the safety requirements for service lifts with rated speeds up to 1 m/s. NOTE For service lifts with higher rated speeds additional requirements shall be applied as appropriate in order to maintain the same level of safety.
Số hiệu tiêu chuẩn
EN 81-3+A1
Tên tiêu chuẩn
Safety rules for the construction and installation of lifts - Part 3: Electric and hydraulic service lifts
Ngày phát hành
2008-07-00
Tiêu chuẩn tương đương
DIN EN 81-3 (2009-12), IDT * DIN EN 81-3 (2010-05), IDT * DIN EN 81-3 (2011-06), IDT * NF P82-410 (2008-10-01), IDT * SN EN 81-3+A1 (2008), IDT * OENORM EN 81-3 (2010-02-01), IDT * PN-EN 81-3+A1 (2008-09-30), IDT * SS-EN 81-3+A1 (2008-08-11), IDT * UNE-EN 81-3+A1 (2008-10-29), IDT * TS EN 81-3+A1 (2012-04-12), IDT * UNI EN 81-3:2008 (2008-11-06), IDT * STN EN 81-3+A1 (2009-01-01), IDT * CSN EN 81-3+A1 (2009-01-01), IDT * DS/EN 81-3 + A1 (2008-11-17), IDT * NEN-EN 81-3:2000+A1:2008 en (2008-08-01), IDT * NEN-EN 81-3:2000+A1:2008 fr (2008-08-01), IDT * SFS-EN 81-3 + A1:en (2009-02-13), IDT
Từ khóa
Definitions * Design * Electrical installations * Electrical transmission systems * Engine rooms * Engines * Hazards * Hoists * Hydraulic lifts * Hydraulic transmission systems * Lift-car * Lifts * Mounting * Occupational safety * Operating instructions * Protection against electric shocks * Protection devices * Protective measures * Reel room * Safety * Safety devices * Safety grips * Safety measures * Safety of machinery * Safety switches * Service lifts * Shafts * Specification (approval) * Supporting means * Workplace safety * Electrical safety * Elevators