Loading data. Please wait

ASTM E 505

Standard Reference Radiographs for Inspection of Aluminum and Magnesium Die Castings

Số trang: 2
Ngày phát hành: 1996-00-00

Liên hệ
1. Scope 1.1 These reference radiographs illustrate the categories and severity levels of discontinuities that may occur in aluminum-alloy and magnesium-alloy die castings. They are intended to provide: 1.1.1 A guide enabling recognition of discontinuities and their differentiation both as to type and severity level through radiographic examination. 1.1.2 Example radiographic illustrations of discontinuities and a nomenclature for reference in acceptance standards, specifications, and drawings. 1.1.3 The values stated in inch-pounds are to be regarded as standard. Note 1-The set of reference radiographs consists of five 81/2 by 11-in. cardboard frames containing radiographs covering discontinuities in aluminum and magnesium alloy die castings. The first four frames each contain two sets of four graded levels of increasing severity, while the last frame contains two ungraded radiographs. The 5 frames are contained in a 101/2 by 111/2-in. ring binder. Note 2-Reference radiographs applicable to aluminum and magnesium castings up to 2 in. (50 mm) in thickness are contained in ASTM Reference Radiographs E155, for Inspection of Aluminum and Magnesium Castings, Volumes I and II. 1.2 Two kinds of illustration categories are covered as follows: 1.2.1 Graded- Three discontinuity categories for aluminum die castings and three discontinuity categories for magnesium die castings, each illustrated in four levels of progressively increasing severity. Category A discontinuities are illustrated for aluminum and magnesium die castings having thicknesses of 1/8 in. (3.2 mm) and 5/8 in. (15.9 mm); Category B discontinuities are illustrated for 1/8-in. thick aluminum and magnesium die castings; and Category C discontinuities are illustrated for 5/8-in. thick aluminum and magnesium die castings. 1.2.2 Ungraded- One illustration of one discontinuity for 0.20-in. (5.1-mm) thickness aluminum die casting; and one illustration of one discontinuity for 1/8-in. (3.2-mm) thickness magnesium die casting. 1.3 This document may be used for other materials, thicknesses, or with other energy levels for which it has been found to be applicable and agreement has been reached between the purchaser and manufacturer. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. IMPORTANT: This standard references radiographic illustrations found in Reference Radiograph E155, ASTM Reference Radiographs for Inspection of Aluminum and Magnesium Castings, Volumes I and II. E155, Volumes I and II are sold separately.
Số hiệu tiêu chuẩn
ASTM E 505
Tên tiêu chuẩn
Standard Reference Radiographs for Inspection of Aluminum and Magnesium Die Castings
Ngày phát hành
1996-00-00
Trạng thái
Hết hiệu lực
Tiêu chuẩn tương đương
ANSI/ASTM E 505 (1996), IDT
Tiêu chuẩn liên quan
Thay thế cho
ASTM E 505 (1991)
Reference Radiographs for Inspection of Aluminum and Magnesium Die Castings
Số hiệu tiêu chuẩn ASTM E 505
Ngày phát hành 1991-00-00
Mục phân loại 77.040.20. Thử nghiệm không phá hủy kim loại
Trạng thái Có hiệu lực
Thay thế bằng
ASTM E 505 (2001)
Standard Reference Radiographs for Inspection of Aluminum and Magnesium Die Castings
Số hiệu tiêu chuẩn ASTM E 505
Ngày phát hành 2001-00-00
Mục phân loại 77.040.20. Thử nghiệm không phá hủy kim loại
Trạng thái Có hiệu lực
Lịch sử ban hành
ASTM E 505 (1991)
Reference Radiographs for Inspection of Aluminum and Magnesium Die Castings
Số hiệu tiêu chuẩn ASTM E 505
Ngày phát hành 1991-00-00
Mục phân loại 77.040.20. Thử nghiệm không phá hủy kim loại
Trạng thái Có hiệu lực
* ASTM E 505 (1990)
Reference Radiographs for Inspection of Aluminum and Magnesium Die Castings
Số hiệu tiêu chuẩn ASTM E 505
Ngày phát hành 1990-00-00
Mục phân loại 77.040.20. Thử nghiệm không phá hủy kim loại
Trạng thái Có hiệu lực
* ASTM E 505 (1975)
Ref. Radiographs for Inspection of Aluminum and Magnesium Die Castings
Số hiệu tiêu chuẩn ASTM E 505
Ngày phát hành 1975-00-00
Mục phân loại 77.040.20. Thử nghiệm không phá hủy kim loại
Trạng thái Có hiệu lực
* ASTM E 505 (1996)
Standard Reference Radiographs for Inspection of Aluminum and Magnesium Die Castings
Số hiệu tiêu chuẩn ASTM E 505
Ngày phát hành 1996-00-00
Mục phân loại 77.040.20. Thử nghiệm không phá hủy kim loại
Trạng thái Có hiệu lực
* ASTM E 505 (2001)
Từ khóa
Aluminium * Die casting * Magnesium * Metallography * Metals * Non-destructive testing * Radiographs * Testing
Số trang
2