Loading data. Please wait

ASTM D 5796

Standard Test Method for Measurement of Dry Film Thickness of Thin-Film Coil-Coated Systems by Destructive Means Using a Boring Device

Số trang: 5
Ngày phát hành: 2010-00-00

Liên hệ
1.1 This test method covers the measurement of dry film thickness (DFT) of coating films by microscopic observation of a precision-cut, shallow-angle crater bored into the coating film. This crater reveals cross sectional layers appearing as rings, whose width is proportional to the depth of the coating layer(s) and allows for direct calculation of dry film thickness. 1.1.1 The Apparatus, Procedure, and Precision and Bias discussions include Method A and Method B. Method A involves the use of an optical measurement apparatus which is no longer commercially available, but remains a valid method of dry film measurement. Method B is a software driven measurement procedure that supersedes Method A. 1.2 The substrate may be any rigid, metallic material, such as cold-rolled steel, hot-dipped galvanized steel, aluminum, etc. The substrate must be planar with the exception of substrates exhibiting " coil set, " which may be held level by the use of the clamping tool on the drilling device. Note 1 -Variations in the surface profile of the substrate may result in misrepresentative organic coating thickness readings. This condition may exist over substrates such as hot-dipped, coated steel sheet. This is true of all " precision cut " methods that are used to determine dry film thickness of organic coatings. This is why several measurements across the strip may be useful if substrate surface profile is suspect. 1.3 The range of thickness measurement is 0 to 3.5 mils (0 to 89 µ m). Note 2 -For DFT measurements of films greater than 3.5 mils (89 µ m), but less than 63 mils (1600 µ m), a 45 ° borer may be used in accordance with this test method, with the exception of 6.8, where the micrometer reading would provide a direct read-out, and division by ten would be unnecessary per 4.3.1 Method A. 1.4 Measurements may be made on coil-coated sheet, certain formed products, or on test panels. 1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Số hiệu tiêu chuẩn
ASTM D 5796
Tên tiêu chuẩn
Standard Test Method for Measurement of Dry Film Thickness of Thin-Film Coil-Coated Systems by Destructive Means Using a Boring Device
Ngày phát hành
2010-00-00
Trạng thái
Có hiệu lực
Tiêu chuẩn tương đương
Tiêu chuẩn liên quan
Thay thế cho
ASTM D 5796 (2003)
Standard Test Method for Measurement of Dry Film Thickness of Thin Film Coil-Coated Systems by Destructive Means Using a Boring Device
Số hiệu tiêu chuẩn ASTM D 5796
Ngày phát hành 2003-00-00
Mục phân loại 17.040.20. Tính chất bề mặt
Trạng thái Có hiệu lực
Thay thế bằng
Lịch sử ban hành
ASTM D 5796 (2010)
Standard Test Method for Measurement of Dry Film Thickness of Thin-Film Coil-Coated Systems by Destructive Means Using a Boring Device
Số hiệu tiêu chuẩn ASTM D 5796
Ngày phát hành 2010-00-00
Mục phân loại 17.040.20. Tính chất bề mặt
Trạng thái Có hiệu lực
* ASTM D 5796 (2003)
Standard Test Method for Measurement of Dry Film Thickness of Thin Film Coil-Coated Systems by Destructive Means Using a Boring Device
Số hiệu tiêu chuẩn ASTM D 5796
Ngày phát hành 2003-00-00
Mục phân loại 17.040.20. Tính chất bề mặt
Trạng thái Có hiệu lực
* ASTM D 5796 (1999)
Standard Test Method for Measurement of Dry Film Thickness of Thin Film Coil-Coated Systems by Destructive Means Using a Boring Device
Số hiệu tiêu chuẩn ASTM D 5796
Ngày phát hành 1999-00-00
Mục phân loại 17.040.20. Tính chất bề mặt
Trạng thái Có hiệu lực
* ASTM D 5796 (1995)
Standard Test Method for Measurement of Dry Film Thickness of Thin Film Coil-Coated Systems by Destructive Means Using a Boring Device
Số hiệu tiêu chuẩn ASTM D 5796
Ngày phát hành 1995-00-00
Mục phân loại 17.040.20. Tính chất bề mặt
Trạng thái Có hiệu lực
Từ khóa
Boring * Coated materials * Coating thickness * Destructive * Destructive testing * Dry film * Finishes * Micrometers * Optical measurement * Testing * Thickness * Thin films * Video cameras
Số trang
5